Yesterday, 03:20 PM
Passed this morning. Thought i'd bombed it but low and behold...... PASS
3 sims up front. Got no drag and drops this time. Several of the multiple choice questions were new. Maybe 4 of the 40 questions were ones not seen here.
The sims:
all my sims were very similar to the ones found here but there were drastic changes on some.
https://www.how2pass.com/emembers/enarsi410/sim/?id=19
VRF & EIGRP Sim:
The IP between R2 and R3 Admin was a 192.168.x.x while all the rest were some form of a 10.x.x.x/30
for this I:
router eig <AS>
network 10.0.0.0
and or
network 192.168.0.0
^^^ that popped all the wings into the EIGRP routing
Next step was to fix some bad autosummarization on R6 with its loopback. I wasn't able to get this but i compared this config to the R5 set up since i figured they should be the same and R5 would be working since not mentioned.
https://www.how2pass.com/emembers/enarsi410/sim/?id=20
DHCP, IP SLA & NetFlow Sim # 2:
The DHCP portion was darn near spot on. Just had to fix the default-router then flip on the interface on the R6 and finally point vlan 20 to the right spot
The change is that they wanted R2, which they called SW2 to use IP SLA tcp-connect down to R5 over tcp 80. The SW was partially set up but the big thing, going down to R5 and flipping on ip sla responder so it'll reply back as needed.
There was no Netflow on this one for me
https://www.how2pass.com/emembers/enarsi410/sim/?id=21
DMVPN OSPF Sim:
Was pretty spot on. The configs were already basically there. Just had to flip on the entire crypto isakmp and ipsec process for H0 and then apply it to the tunnel. There was a note that the BR1 and 2 needed to establish connection directly to one another. I wasn't able to get this to work and the show dmvpn on the BR1 and 2 only showed the hub but the Routers and Sw were able to ping one another just fine.
Remember: Study and know WHY you are doing what you are doing. Not just rote muscle memory.
3 sims up front. Got no drag and drops this time. Several of the multiple choice questions were new. Maybe 4 of the 40 questions were ones not seen here.
The sims:
all my sims were very similar to the ones found here but there were drastic changes on some.
https://www.how2pass.com/emembers/enarsi410/sim/?id=19
VRF & EIGRP Sim:
The IP between R2 and R3 Admin was a 192.168.x.x while all the rest were some form of a 10.x.x.x/30
for this I:
router eig <AS>
network 10.0.0.0
and or
network 192.168.0.0
^^^ that popped all the wings into the EIGRP routing
Next step was to fix some bad autosummarization on R6 with its loopback. I wasn't able to get this but i compared this config to the R5 set up since i figured they should be the same and R5 would be working since not mentioned.
https://www.how2pass.com/emembers/enarsi410/sim/?id=20
DHCP, IP SLA & NetFlow Sim # 2:
The DHCP portion was darn near spot on. Just had to fix the default-router then flip on the interface on the R6 and finally point vlan 20 to the right spot
The change is that they wanted R2, which they called SW2 to use IP SLA tcp-connect down to R5 over tcp 80. The SW was partially set up but the big thing, going down to R5 and flipping on ip sla responder so it'll reply back as needed.
There was no Netflow on this one for me
https://www.how2pass.com/emembers/enarsi410/sim/?id=21
DMVPN OSPF Sim:
Was pretty spot on. The configs were already basically there. Just had to flip on the entire crypto isakmp and ipsec process for H0 and then apply it to the tunnel. There was a note that the BR1 and 2 needed to establish connection directly to one another. I wasn't able to get this to work and the show dmvpn on the BR1 and 2 only showed the hub but the Routers and Sw were able to ping one another just fine.
Remember: Study and know WHY you are doing what you are doing. Not just rote muscle memory.