Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
EIGRP Query Storm
#1
Hello,

I have the following Problem with the topology below. If the connection between as1_r1 and as1_r6 or as1_r3 and as1_r7 flaps one time, all routers gets a high CPU load and the route 10.1.16.0/21 (the summary is configured on as1_r6 and as1_r7 on the serials) is in eigrp active state all time, because every router queries for this route....

One solution is to shut down one serial on as1_r{1,2,3} or to configure as1_r6 or as1_r7 as a stub router, but I think there should be another solution.

If needed, I could post the configurations...

Thanks in Advance
Viets

[code]as1_r1#sh ip eigrp topology  active
IP-EIGRP Topology Table for AS(1)/ID(91.189.94.4)

Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
       r - reply Status, s - sia Status

A 10.1.16.0/21, 1 successors, FD is Inaccessible, QR
    3 replies, active 00:00:00, query-origin: Successor Origin
        via 10.1.1.11 (Infinity/Infinity), Serial1/0, serno 59115
        via 10.1.16.1 (Infinity/Infinity), r, Serial1/1, serno 59125
        via 10.1.1.2 (Infinity/Infinity), r, R, FastEthernet0/0, serno 59122, anchored
        via 10.1.1.10 (Infinity/Infinity), Serial1/0, serno 59124
      Remaining replies:
         via 10.1.1.3, r, FastEthernet0/0
[/code]

[Image: topology3.png]

[code]
as1_r1#sh ip int brief
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            10.1.1.1        YES NVRAM  up                    up       
Serial1/0                  10.1.1.9        YES NVRAM  up                    up     
Serial1/1                  10.1.0.1        YES TFTP   up                    up     
Loopback0                  10.1.0.1        YES NVRAM  up                    up     
Loopback1                  91.189.94.4     YES NVRAM  up                    up     

as1_r2#sh ip int brief
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            10.1.1.2        YES NVRAM  up                    up     
Serial1/0                  10.1.1.10       YES NVRAM  up                    up         
Loopback0                  10.1.0.2        YES NVRAM  up                    up   

as1_r3#sh ip int brief
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            10.1.1.3        YES NVRAM  up                    up     
Serial1/0                  10.1.1.11       YES NVRAM  up                    up       
Serial1/2                  10.1.0.3        YES TFTP   up                    up     
Loopback0                  10.1.0.3        YES NVRAM  up                    up     
Loopback1                  10.1.8.1        YES NVRAM  up                    up     

as1_r6#sh ip int brief
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            10.1.17.1       YES NVRAM  up                    up       
Serial1/0                  10.1.16.1       YES TFTP   up                    up     
Loopback0                  10.1.16.1       YES NVRAM  up                    up 

as1_r7#sh ip int brief
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            10.1.17.2       YES NVRAM  up                    up       
Serial1/0                  10.1.16.2       YES TFTP   up                    up     
Loopback0                  10.1.16.2       YES NVRAM  up                    up

[/code]
Reply
#2
Hello,

I've found the problem, the summaries were configured with the administrative distance of 220, this is higher than 90 from eigrp so this was the bug...

this thread can be closed/deleted...

greetings
Viets
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)