| Welcome, Guest |
You have to register before you can post on our site.
|
| Latest Threads |
AR567
Forum: CCNP ENARSI 300-410 Forum
Last Post: genzdhal
10 hours ago
» Replies: 0
» Views: 16
|
PBR and Redistribution Si...
Forum: CCNP ENARSI 300-410 Forum
Last Post: serbancalin
Yesterday, 10:16 AM
» Replies: 1
» Views: 1,596
|
simlets and/or simulation...
Forum: CCNP Security - SCOR 350-701 Forum
Last Post: ncc16ncc
Yesterday, 09:52 AM
» Replies: 2
» Views: 3,765
|
AR405
Forum: CCNP ENARSI 300-410 Forum
Last Post: help_desk
Yesterday, 09:38 AM
» Replies: 1
» Views: 55
|
Answers NOT being "correc...
Forum: Site News & Issues
Last Post: JamesJones
12-14-2025, 09:53 PM
» Replies: 2
» Views: 98
|
Inaccurate questions/answ...
Forum: Site News & Issues
Last Post: JamesJones
12-14-2025, 09:52 PM
» Replies: 5
» Views: 397
|
AN1112
Forum: Answer this question
Last Post: help_desk
12-14-2025, 02:49 PM
» Replies: 1
» Views: 90
|
QID:AN1036
Forum: Answer this question
Last Post: help_desk
12-14-2025, 11:41 AM
» Replies: 1
» Views: 1,494
|
Explanation is incorrect
Forum: Exam Experience
Last Post: help_desk
12-14-2025, 11:26 AM
» Replies: 1
» Views: 96
|
QID:AND84
Forum: Answer this question
Last Post: help_desk
12-14-2025, 11:03 AM
» Replies: 3
» Views: 1,083
|
|
|
| AR291 |
|
Posted by: darkfile - 02-15-2023, 10:54 PM - Forum: CCNP ENARSI 300-410 Forum
- No Replies
|
 |
Is the diagram for AR291 missing?
Without a diagram, how do we know the loopback IP addresses for source and destination to decide the right answer?
|
|
|
| Explain answer for AR208 |
|
Posted by: darkfile - 02-15-2023, 09:31 PM - Forum: CCNP ENARSI 300-410 Forum
- Replies (2)
|
|
Can someone help me with the answer for AR208?
I do not understand it. Maybe there is a network diagram missing?
When I configure a similar setup in GNS3, I get the network advertised. I do not need the "ip ospf network point-to-point" command to have the loopback route advertised in OSPF.
|
|
|
|
| AR271 |
|
Posted by: CSEngRM - 02-15-2023, 01:16 PM - Forum: CCNP ENARSI 300-410 Forum
- Replies (3)
|
|
The only logical answer is to configure AS_PATH prepend for the current best path.
Higher local pref is preferred so the current answer seems incorrect?
|
|
|
|
| (QID:AR482) |
|
Posted by: sayoob - 02-14-2023, 10:47 PM - Forum: CCNP ENARSI 300-410 Forum
- Replies (1)
|
|
(QID:AR482) What is a characteristic of IPv6 RA Guard?
I saw this question twice and the answers were different
one time was
It is unable to protect tunneled traffic
the next time was
it filters rouge RA broadcasts from connected hosts
which one is the correct answer?
|
|
|
|
| QID:AR411 |
|
Posted by: darkfile - 02-09-2023, 02:47 PM - Forum: CCNP ENARSI 300-410 Forum
- Replies (2)
|
|
Hello I think the answer here is incorrect.
It says "Allow the NA and NS messages, which are denied by the implicit deny".
However, in IPv6 ACLs, the Neighbor Discovery is implicitly allowed:
https://www.cisco.com/c/en/us/support/do...cl-00.html
>> Each IPv6 ACL contains implicit permit rules to enable IPv6 neighbor discovery. These rules can be overridden by the user by placing a deny ipv6 any any statement within an ACL.
Can you please check?
|
|
|
|
| AR235 |
|
Posted by: CSEngRM - 02-07-2023, 06:23 AM - Forum: CCNP ENARSI 300-410 Forum
- Replies (1)
|
|
Do the customer site routers need the "ip vrf forwarding A" command?
Is the selected answer correct because the customer routers are using VRF-Lite?
|
|
|
|
|
