| Welcome, Guest |
You have to register before you can post on our site.
|
| Latest Threads |
QID: AR677 Answer is wron...
Forum: CCNP ENARSI 300-410 Forum
Last Post: elpotatoexperto
7 hours ago
» Replies: 1
» Views: 25
|
Failed Exam 6/17
Forum: CCNP ENARSI 300-410 Forum
Last Post: help_desk
06-20-2026, 07:12 AM
» Replies: 2
» Views: 467
|
Just Passed! Corrected La...
Forum: CCNP ENARSI 300-410 Forum
Last Post: forumsupport
06-15-2026, 03:00 AM
» Replies: 2
» Views: 11,521
|
CoPP Configuraton Simulat...
Forum: CCNP ENARSI 300-410 Forum
Last Post: help_desk
06-10-2026, 07:05 AM
» Replies: 1
» Views: 416
|
QID: AR188 - Question/Ans...
Forum: CCNP ENARSI 300-410 Forum
Last Post: help_desk
06-04-2026, 07:05 AM
» Replies: 1
» Views: 514
|
Failed
Forum: CCNP ENARSI 300-410 Forum
Last Post: help_desk
05-30-2026, 07:16 AM
» Replies: 2
» Views: 820
|
SIM down?
Forum: General Discussion
Last Post: elpotatoexperto
05-29-2026, 11:29 AM
» Replies: 2
» Views: 763
|
QID:AR677 Incorrect Answe...
Forum: CCNP ENARSI 300-410 Forum
Last Post: forumsupport
05-23-2026, 04:41 AM
» Replies: 3
» Views: 6,166
|
BGP Troubleshooting Sim
Forum: CCNP ENARSI 300-410 Forum
Last Post: help_desk
04-30-2026, 09:50 AM
» Replies: 1
» Views: 1,074
|
Sim Time
Forum: CCNP ENARSI 300-410 Forum
Last Post: elpotatoexperto
04-23-2026, 04:16 PM
» Replies: 3
» Views: 1,489
|
|
|
| Passed today 07-04-2023 |
|
Posted by: aoliveira - 07-04-2023, 06:38 PM - Forum: CCNP Security - SCOR 350-701 Forum
- No Replies
|
 |
Passed the exam today, how2pass material helped a lot at least in my exam just three or four new questions one of them I remember it was drag and drop and related to add a server using tacacs process configuration but it was easy one very intuitive.
Good luck for all.
|
|
|
| QID:SCR284 |
|
Posted by: xpoxpo - 06-06-2023, 02:59 PM - Forum: CCNP Security - SCOR 350-701 Forum
- Replies (1)
|
 |
Answer is shown as "802.1X and MAB will both be used and ISE can use policy to determine the access level", but MAB isn't configured on the interface (in the exhibit), so I don't think this answer is correct.
I believe the answer should be "802.1X will work and the device will be allowed on the network"
|
|
|
| AN733 |
|
Posted by: vjuliusv - 06-06-2023, 02:19 AM - Forum: General
- Replies (1)
|
 |
Hello,
The answer which is marked as correct in this question references broadcast IPs within the respective subnets in the diagram and the subnet masks in the router configs don't fit the CIDRs referenced. I believe this should be:
R7#
interface FastEthernet1/0
ip address 10.88.31.126 255.255.255.192
R8#
interface FastEthernet0/0
ip address 10.19.63.94 255.255.255.240
R9#
interface FastEthernet1/0
ip address 10.23.98.158 255.255.255.224
But this specific answer is not referenced within the question. Am I missing something?
|
|
|
|