Had a Sim to collect vtp info, configure new switch and configure management ip and default gateway.Passed with a 930 using H2P and New Horizon  ;D ;D

Says auto-summary must be disabled on N1 and B1 before traffic can flow between 172.16.8.0 and 10.10.16.0. But looking at the routing tables It looks like 172.16.8.0 has a clear path to 10.10.16.0

I don't know how to post exhibits otherwise I'd help further

Hello everyone...

Last friday I passed ICND1 (974). At present, I am preparing for ICND2.
I strongly recommend for those who want to pass, to understand all of H2P questions, before taking an exam.

My study materials:
CCENT/CCNA  ICND1 - W. Odom
CBT nuggets video for ICND1
H2P tests.

Michał.

Just getting started and studying for my CCENT right now.  Is there any way to save your test results in the practice exams as a document instead of having to Print up 20+ pages.  I tried saving as an HTML file, however you can not see the Exhibits when you do this.  Any help would be greatly appreciated.
Thank you

The networks connected to router R2 have been summarized as a 192.168.176.0/21 route and
sent to R1. Which two packet destination addresses will R1 forward to R2? (Choose two.)
A. 192.168.194.160
B. 192.168.183.41
C. 192.168.159.2
D. 192.168.183.255
E. 192.168.179.4
F. 192.168.184.45
Answer: B, E
Why answer B,E correct? why other options are incorrect?



The Ethernet networks connected to router R1 in the graphic have been summarized for router
R2 as 192.1.144.0/20. Which of the following packet destination addresses will R2 forward to R1,
according to this summary? (Choose two.)
A. 192.1.159.2
B. 192.1.160.11
C. 192.1.138.41
D. 192.1.151.254
E. 192.1.143.145
F. 192.1.1.144
Answer: A, D
Why answer A,D correct? why other options are incorrect?

Hi,
I build lab5 with gns3 and in my simulation the network 172.16.1.0 / 24 is not advertises by R3 to its neigbor R4.
It will be only advertised if I either put a network statement 172.16.0.0 or redistribute connected command under router eigrp.
There is some cisco doc about eigrp stub connected ....
http://www.cisco.com/en/US/docs/ios/12_0...rpstb.html
but it is not really clear. It says:
-------
The connected keyword will permit the EIGRP Stub Routing feature to send connected routes. If the connected routes are not covered by a network statement, it may be necessary to redistribute connected routes with the redistribute connected command under the EIGRP process. This option is enabled by default.
------
It may be neccessary .... ??? Depending on what ?
If I put a network 172.... command, I dont need a redistribute connected at all, right ? If I put redistribute connected, I dont need the eigrp stub ____connected____ option, so ?
Confused .
Any ideas to find a logic in there ?
Evesan

Passed CCENT exam today, thanks how2pass.  going for ccna 60 days or less

Hi please assist people I just flunked with a score of 735. I got 25% score on Nat and ACL, describe how networks work 75%, configuring and verifying switch with vlans 69%, implementing IP addressing scheme 50%. My lowest mark was NAT and ACL is there any body out there who can please help out with the practice as I have had many sleepless nights studying only to flunk.

Passed the ROUTE exam yesterday with a credible 953/1000. There's no doubting that how2pass is a great help but you really need to understand the concepts of how everything works to feel comfortable. The CCNP ROUTE book by Wendell is worth getting and reading!

50 Questions, a lot of EIGRP and OSPF, 4 SIMS; PBR, OSPF STUB, OSPF/EIGRP Redistribution, EIGRP ip summary-address. Some of the configuration isn't as it is in what how2pass have on their site, hence you need to have a good knowledge of the IOS and where to look. I was unaware that the ? command does sometimes give you some help on some of the sims and don't worry if the copy run start command doesn't work.

1 exam away from CCNP now :-D

i understand how you get 1022 subnets and 510 subnets of of what looks like class c subnets, since the question is about a class b, but i don't understand why they need to be broken up in the first place: 126 hosts and 510 subnets looks like exceeding the requirements, so why do i even need 62 extra hosts and 1022 subnets, what am i missing?