Wanted to share this awesome website i came across. Wish it was around when I was studying for the CCNA exam; http://www.freeccnaworkbook.com

I was running through a "test mode" run and QID: NA720 came up but no exhibit is shown, no button or image.

The question clearly requires something else visually as it can't be answered just from the text.

I tried the question again both after the test run and as an individual question. I also tried a second browser (IE8) with the same problem.

I'm using FireFox 3.6.13 with the recommended settings as far as pop-up blocker, etc. I've done nearly every question available on this computer/browser with no problems.

I honestly don't believe that I could have done it without how2pass.com - the study questions were invaluable in determining where my weaknesses lay.

I was a bit skeptical when my instructor insisted that I register and pay for how2pass - but I did and then when I saw how badly I was doing in the tests, I buckled down and got to work. I stayed away from the simulations section out of fear - but it was REALLY worthwhile once I did them as I got a couple of very similar sims in the exam itself (ACLs and EIGRP) and was able to handle them beautifully

Took only 40 minutes to finish the exam - it sounds obvious, but once you know what you're doing it's just a matter of clicking through the answers - thanks to how2pass, I was able to do subnetting out of my head.

I am happy I finally took the test and I got a 974.  Just like everyone else on here who passed this test study How2pass and get 90%+ on the random tests steady and you will be fine.

I am confused by the seemingly different answers given by the two questions in regards to the port speed requirements for 802.1Q VLAN trunking.

QID: NA301 says "Yes, it's true that 802.1Q trunks can use 10Mbps Ethernet but it is not common practice and not recommended".

In addition there is a link that states in part: "802.1Q encapsulation is now available on the built-in 10BaseT Ethernet interfaces of the Cisco 2610, 2611, and 2612..."


Now in QID: N254 asks "[switch with 3 VLANs, router on a stick]...What type of interface is necessary on the router if only one connection is to be made between the router and the switch?"

The correct answer according to how2pass is 100 Mbps Ethernet.


Is there a problem here, is one question incorrect, or am I missing something?

I've had this question several times and I always get it wrong. Just now I've tried doing it 3 times individually and I got marked wrong all times.

I checked all the cable types and ip addresses correct, and I even did "enable password" correctly instead of secret. Everything I've entered (did copy run start also) looks the SAME as the explanation!!!

Anyone else having problems with this one?


I also just got done doing S17 and got marked wrong... I did it again even using the number 101 for my access list and got marked wrong again a second time......

access-list 101 permit tcp host PCIP host SERVERIP eq 80
access-list 101 deny tcp any host SERVERIP eq 80
access-list 101 permit ip any any

int fa0/0 (interface the server is on)
ip access-group 101 out

Did copy run start also, and I've checked my answers against the explanations and they are IDENTICAL. What gives with these sims???

I am trying to decide which exam to begin my studies for the CCNP track.  Based on an understanding of the skills learned which exam is recommended as the beginning course?  I would like a recommendation as to which CCNP exam Routing or Switching would be most effect to take first. Thanks in advance for sharing your insight.

I had my CCNA and lost it due to being lazy and not taking another exam.  So today I took and passed the new 640-802 CCNA test using how2pass and job experience.  During the test there were 3 Labs, which were Access-list, EIGRP, and VLAN. 

Good luck and study hard. 

Hi,

Could anyone please tell me if I want to connect a router's ethernet(ethernet!) interface to CATALYST 3550 gigabitethernet interface what shoud I do?

My ultimate target is to connect the router to a pc (catalyst 3550 will be in the middle). Router's ethernet interface connected to switch's one gigabitethernet port and switch fa 0/1 interface to pc's ethernet port. I wonder how to do that.

Thanks in advance.

Question N192 accepts only one answer (radio buttons) but it seems to have two correct answers.

The question asks about the output of "show vtp status".

The answer according to system is:
"Learn and save VTP configuration in the running configuration."

I chose this answer:
"VTP is not saved to NVRAM."

In the answer section there is a detail explanation and under "Client", the mode the switch is operating in, there is this line highlighted in blue:
"Client configuration is not saved to NVRAM, it resides in running configuration only."

Both my answer and the "correct" answer are explicitly referenced. Aren't the both correct?

Maybe the question should be multiple choice?