Hello All
THis summer I am thinking of doing certifications of CCNA and CNNP. I have the following question.
1)Should I just prepare for CCNP or should I first do CCNA and thne start CCNP.
2)Is it possible to do both CCNa and CCNP in three months(in summer I am free). If yes, how should I go about, assuming I will be studying on my own.
Your help will be appreciated a lot!!
Thanx

i got two of them but select the rip v1 one over IGRP.

this is the passive-interface question. My understanding is that passive interface dont send out routing info but will still recieve routing updates.

ok so i understand why the RIP one wont work - it's becuase of the passive interface deault which means rip routes not being sent out of s0/1 to rtc so rtc wont know how to get to RTA.

but ...

in teh IGRP config we also have passive interface enable with the no passive on s0/1 ??? so igrp goes out of s0/1 but how will rta know about rtc if s0/0 is passive which is the link to RTA? surely s0/0 should be no passive as well????



Thanks
Bal

hi and hello.

guys what do you think of the follow gear(lab)
I am preparing for CCNP and come across an auction selling the following

x1 2611XM Cisco router
x1 2520 Cisco router
x2 2501 Cisco router
x1 2511 Cisco router
x1 2503 Cisco router
x1 1900 Cisco switch
x1 2900xl Cisco switch

x1 1900 Cisco switch (front panel is broken)
x1 3com 10MB switch

x1 Rextron KNV2116d with cables (missing 9v power supply, will keep looking for it)


*********************

Will this be enough
and cost wise what will be reasonable???

Ta

Ok these two drag and drop subnet questions both puzzle me for many reasons

1/ the questions ask for you to use subnet zero and to conserve host addresses for future use but both questions miss 4 host addresses when
allocating addresses to the serial interfaces n418 issues 192.168.91.197 to the serial link but the next usable host address is 192.168.91.193 so there is 4 missing hosts here and same thing occurs on question n419 where hosts 80-84 are not used

2/ when allocating hosts you should always issue your highest number of hosts to lowest so why does n419 allocate the 78 hosts their subnet last?

3/ going by the same principle of highest to lowest why does the serial link in n418 appear in the middle of the allocation?

4/ why is subnet zero not used in n418 if it is telling you it is in use?

this questions threw me off as they make no sense whatsoever and come with no explanation of how the answer was arrived at


please explain  ???

I've been rolling with how2pass since my first test!  Excellent practice exams and simulators.  Thx How2Pass!

I thought an access list was applied to a router interface as outbound if it is exiting the LAN segment and inbound if it is arriving into the LAN segment from a different segment. So I'm confused as to why the correct answer is shown as

ip access-group 101 in

Should this not be out, since the frame from host 1 will be exiting the FA0/0 interface, heading outbound to the server? I'm so confused.

I had three Labs and one Simlet:

Labs -
OSPF Stub
ISIS/EIGRP Redistribution
IPV6 Virtual Links ???????????? Got it right and I'm not sure how?

Simlet -
EIGRP Topology Output

This is the first time that I have ever taken a certification test and by the end of it I thought that I had failed.  I got crushed with IPV6 and Multicast questions.  I had problems with the Labs.  Once I got into the labs, I couldn't minimize the the telnet session to get into the other router.  I wasted 15 minutes trying to figure out what to do.  Luckily, I was able to telnet from router to router to finish my configuration.  Make sure that you verify your lab configuration because one of my commands didn't show up on the config (what a disaster).  I got a lot of questions that were not on How2Pass and AT.  How2Pass and the other materials helped me get through the exam.

Materials I used:

Training Course and Courseware
CBT Nuggets
How2Pass
AT
Exact Exam Study Guide
Boson Labs
And of Course Real World Experience       

There's a problem with this drag-n-drop question. The IP of the remote server "128.77.88.166" needs to be placed at two places but when you drag it the second time, the IP address changes to 128.77.88.156, which in result, marks the question wrong. Please fix this problem, Thanks!

I'd love to get a hold of the stencils used to prepare the exam questions. Any leads?
Thanks,
Chris

I am finally CCNP Certified ;D ;D ;D  My last exam was ISCW and I scored a total of 1000! I couldn't have done it without the help of How2pass. You have excellent material and many of the things that i didn't grasp while reading Cisco Press books, I got through all your links and explanations to the questions.
Great work guys !  Thanx for all your help ! I will surely recommend you to all my fellow co-workers!

Thanx